Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Somerton Homeowners
Water is the slowest and most expensive problem a chimney has. Mortar joints get soft, brick faces flake, flashing pulls away from the roofline, and by the time a stain shows up on the ceiling inside, the damage has usually been working for a couple of seasons. We handle the whole chimney, not just the sweep, so a repair that starts with a cracked crown doesn’t need a second contractor to finish. Our technicians have up to 8 years of experience working on Somerton’s older masonry chimneys and on newer prefab systems, and we’ll tell you plainly what we found and what it means for your home’s safety. If you’d rather talk it through first, call (855) 528-0951.
What Our Chimney Repair Service Includes
Masonry repair is where a lot of generalist crews stop and a chimney specialist starts. Each of the jobs below involves the flue or the structure around it, so it affects how the whole system drafts, sheds water and vents. We do all six under one roof.
Mortar Repointing
Repointing is cutting out crumbling mortar from the joints and replacing it with fresh mortar that bonds to the brick and stays put. You need it when the joints are recessed, sandy or falling out in chunks, which lets water straight into the wall. We rake the joints to the right depth and match the mortar mix to the brick so the repair doesn’t crack the faces it’s supposed to protect.

Spalling Brick Repair
Spalling is when the face of a brick pops off or flakes away, usually because trapped moisture froze and pushed outward. It shows up as rough, pitted brick with sharp edges and rubble sitting on the roof or the flashing. We replace the failed brick and find the water source that caused it, because new brick on a leaky chimney will spall the same way.

Chimney Waterproofing
Waterproofing is a breathable coating applied to the masonry that keeps rain out while letting moisture inside the chimney escape as vapor. It’s the right call for brick that’s structurally sound but soaking up water every storm. Sealing a chimney that’s still leaking from the crown or flashing just traps the problem, so we fix the water entry first and waterproof after.

Flashing Repair
Flashing is the metal that seals the joint where the chimney passes through the roof, and it’s where a large share of chimney leaks begin. When the flashing pulls loose, rusts through or was never stepped into the shingles properly, water runs down the chimney and shows up as a ceiling stain far from the fireplace. We reset or replace the flashing and tie it back into the roofing so the seal works with the roof, not against it.
Chimney Rebuilding
A rebuild is for chimneys that have gone past repair at the top: loose courses, a leaning stack, or brick that crumbles when you touch it. We take the chimney down to solid masonry and rebuild it with new brick and mortar, keeping the flue and its clearances intact. It’s the most demanding job in the trade, and it’s also the one that puts a chimney back on solid footing instead of patching it every year.
Tuckpointing
Tuckpointing is the finer version of repointing, where the mortar joint is shaped and finished to leave a clean, slightly raised line that sheds water and looks deliberate. It’s used on chimneys where appearance matters as much as the seal, and on older brick where the joint profile is part of the character of the house. We grind out the old mortar carefully so we don’t chip the brick edges, then finish the joint by hand.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We install and work with professional-grade materials from brands most homeowners never hear about until something goes wrong: DuraFlex, Olympia Chimney, Famco and Copperfield, along with HeatShield and Gelco for relining and restoration. These are the components commercial and specialty chimney contractors use, not the generic covers and kits sold at a hardware store. A DuraFlex flexible stainless liner, for example, is built to handle an offset flue that a rigid liner simply can’t follow, which is why we can take on reline jobs that rigid-only crews have to turn down. We know where each of these products wears out, and we know what a proper installation of each one looks like.
Whether your chimney has an Olympia Chimney cap, Famco components, a Copperfield crown or a DuraFlex liner, we can inspect it, repair it and replace what’s failed without guessing at the brand. We’re not a dealer and we don’t claim to stock anyone’s parts on a shelf, but we work with these systems often enough to know their failure points and their fit. Whether you have Olympia Chimney, Famco, Copperfield, DuraFlex or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Crumbling or missing mortar joints. If you can push a screwdriver into the mortar between bricks, it’s gone soft and water is getting in. Loose joints left alone lead to spalling brick and, eventually, a chimney that needs rebuilding instead of repointing.
- White chalky stains on the brick. That powdery bloom is water moving through the masonry and leaving minerals behind as it dries. It’s a sign the chimney is soaking up rain, and it usually means the waterproofing has failed or was never there.
- Rust streaks or water stains on the ceiling near the chimney. This points to flashing or crown failure, and the leak is often several feet from where the stain appears. Water that reaches the ceiling has already passed through the framing, so it’s worth checking before the next storm.
- Brick flakes or rubble on the roof or in the firebox. Falling brick faces mean spalling is active and the chimney is losing material with every freeze. Small pieces on the roof are the early warning; larger chunks mean the structure above needs attention soon.
- A leaning or visibly cracked chimney stack. Cracks that run through the brick, or a stack that’s pulling away from the house, are structural and shouldn’t wait. This is the one sign where we’d rather hear from you today than next season.
Our Chimney Repair Process – Step by Step
- 1
We start with a full inspection, not a sales pitch. We look at the crown, the flashing, the brick, the mortar joints and the flue interior, and we take photos as we go. If a camera inspection of the flue is needed, you see the footage too, so nothing is recommended on our word alone.
- 2
We explain what we found in plain terms. You get a written explanation of what’s failing, why it matters, and what happens if it waits a season. If part of the chimney is fine, we say so, because a repair estimate that pads the job costs you trust and costs us the next call.
- 3
We give you a written estimate before any work starts. The price is set per job by that estimate, and there’s no charge for the estimate itself. You’ll know the scope and the cost before we pick up a trowel.
- 4
We do the repair with the right materials. That might be mortar matched to your brick for repointing, heat-rated sealant and new flashing at the roofline, or a HeatShield application to restore a deteriorating flue interior without tearing the chimney down. Professional-grade components go in from the start.
- 5
We show you the finished work and how to keep it that way. We walk the repair with you, point out what to watch for, and tell you when the next sweep or inspection makes sense. Your flue is a system, and we treat it like one.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Somerton?
Chimney repair in Somerton is priced per job, and the range depends heavily on how much water damage the chimney has already taken. The figures below are typical estimates, not quotes; the written estimate you get after inspection sets the final price.
| Repair | Typical Estimated Range | What Drives the Price |
|---|---|---|
| Mortar repointing | $450 – $1,200 | Height of the chimney, number of joints, access to the roof |
| Tuckpointing | $600 – $1,500 | Finished joint work, brick condition, square footage |
| Spalling brick repair | $500 – $1,400 | Number of brick replaced, extent of the water source |
| Chimney waterproofing | $350 – $800 | Chimney size, masonry condition, prep work needed |
| Flashing repair | $400 – $1,000 | Roof pitch, flashing type, whether the shingles need to be reset |
| Partial chimney rebuild | $1,800 – $4,500 | How far down the damage goes, brick and mortar match |
| Full chimney rebuild | $5,000 – $12,000 | Chimney height, flue configuration, structural condition |
What affects the price most is access and extent. A chimney on a steep roof takes longer to work on safely than one on a low pitch, and a repair that starts at the crown often reveals soft mortar further down once the loose material comes off. The way to avoid overpaying is to fix the water source before it spreads, because repointing a chimney today is a fraction of rebuilding it after a few more winters. Everything we recommend comes with camera or photo evidence you can see for yourself, and if a repair can safely wait a season, we’ll tell you that too. Our free estimate includes the inspection, the photos and a written scope. For an exact quote, call (855) 528-0951.
Chimney Repair Near Somerton – Our Service Area
We work across Somerton and the surrounding communities, including Woodbourne, Warwick, Churchville, Croydon, Richboro, Horsham, Oreland, Bristol, Levittown, Fairless Hills and Newtown. Response times depend on the job and the day, and we book each repair around the estimate so you’re not left waiting on a window. If you’re nearby and need chimney repair or chimney repair in a neighboring town, we can help there too. For the full range of what we do, start with Chimney Sweep Somerton.
Serving Somerton, PA – Our Local Coverage Area
We serve Somerton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Somerton
Chimney repair is fixing the parts of the chimney system that have failed from water, freeze-thaw cycles or age: mortar joints, brick faces, flashing, the crown, and the flue interior. It’s different from a sweep, which removes creosote and clears the flue, though the two often go together. If you’re not sure which one you need, our inspection tells you, and we can handle chimney repair and sweeping in one visit.
Most repairs take a day or less: repointing, waterproofing and flashing work are usually completed in a single visit. A partial or full rebuild is a bigger job and can run several days depending on the size of the chimney and the weather. We give you a realistic timeline with the written estimate so you can plan around it. Call (855) 528-0951 for an exact quote – estimates are free.
Typical estimates in Somerton run from about $350 for waterproofing to $1,200 for repointing, with flashing work around $400 – $1,000 and a full rebuild in the $5,000 – $12,000 range. The final price depends on the extent of the damage and how accessible the chimney is. The written estimate sets the price, and the estimate itself is free. Call (855) 528-0951 for an exact quote.
Yes. We install and repair DuraFlex flexible stainless liner systems and work with Olympia Chimney components, along with Famco and Copperfield. These are professional-grade products, and we know their failure points, which matters when a liner or cap needs replacing rather than patching. If you have another make, we can still help.
Same-day service is possible depending on the job and the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. For a non-emergency repair, calling ahead gets you on the schedule sooner.
We stand behind the workmanship on the repairs we perform, and the materials come with the manufacturer’s coverage that applies to that product. The specifics are put in writing with your estimate so you know what’s covered before work begins. If you’d like the details for your particular repair, ask when you call (855) 528-0951.
Clear access to the fireplace and the hearth, and move anything breakable away from the work area. If we need to be on the roof, make sure we can reach it and that pets are inside. Beyond that, you don’t need to do anything; we bring the materials and handle the setup. For liner and rebuild work, see our chimney liner and rebuild page, and for fireplace issues, our fireplace repair service covers that side of the system.
Schedule Your Chimney Repair Service in Somerton Today
A small repair now is cheaper than a rebuild later, and the inspection that tells you which one you need is free. We handle the whole chimney, from the crown and flashing to the flue liner, using professional-grade materials and a written estimate before any work starts. Call (855) 528-0951. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. No-obligation estimate, and we’ll tell you straight if the repair can wait.
Written by the team at Chimney Sweep Somerton.